Видео

Thanks so much for this! Fixed my shower all by myself for a fiver.Also saved a lot of inconvenience.

I find that the mixing dial is very stiff and is difficult to turn especially when wet as there is no grip on dial itself. Any ideas how to fix? Thanks.

Oh great video by the way

Hi what size copper compression fittings are use on this shower? Thanks

Just installed my Omnicare SE, but it's beeping when we turn it on and off. How do we change the dip switches so it doesn't auto turn off, but also doesn't beep?

New shower fitted not heating always going back to cold

No pictures

At 27secs. How do I get the water running to flush out debris and air from the pipe?

That bloody music !!

You look like the king of Jordan

Wow its so silent, and with wn immaculate linear flow😅

My AS2000SR doesn't seem to have a cool setting, it goes from hot to scalding hot even on the lowest settings. It is constantly set to the lowest temperature and I have to make sure the water tank isn't really hot before I shower to have a more comfortable shower, is this a solveable problem? I'm the only one in the family brave enough to use it!

Would replacing this stop ours dripping or does the whole valve need replacing? Thx.

If is a pipe from ceiling under unit can that drop the preasure or would improveing to fit in the top of unit

Thanks! This saved us calling out a professional, we sorted out our shower within 2 minutes.

What does the orange bit do

You are filming too far away

I have bought yesterday from Screwfix. I gonna install today. This video is very helpful. Thanks !

If pipe entry is from rear as in video it says in instructions to seal around with mastic. But does not show this on video.

Looks easy enough unless, like me, you can barely see the cover screws never mind loosen them! The downside of getting old. 😬

Hi I change my triton shower for this new Omnicare but the pressure is going down the old one are much power any way to improve back pressure thanks

What position should the hot and cold dial be at when placing the face plate on ....... the temp guage doesnt make sense

But...why

Hi I’ve fitted the T 80 z and can’t get any heat at all what might be the problem thanks in advance, and great content

No silicone around the sides of the unit? What about protecting the screw holes, ans water pipe and electrical cable hole?

Perfect. The water is now so hot I can see steam! Such an easy solution. Thank you.

Hello I moved into a property with this shower in it When i turn it on, it takes about 30 seconds for the water to go from completely cold to ideal What would be causing this? The previous house i lived, had a different old shower, which never did this

No mention of the correct compression fitting to use on the water inlet! Are copper olives ok or do you also need a pipe insert? (TSM???)

8 and 11 litres p/m at what temperature. If it is at cold water or 40 degrees C makes a shower usable or not 3L p/m is pointless.

It may be useful to someone: but, the part at 3:00 where the water flows steadily out the hose, that took 15 mins and some sucking ("said the actress to the bishop") before I got a steady flow on my install. Great video, thank you, very useful.

Had real issues with the switches on these.

my triton shower button doesnt work. But the ceiling pull cord turns water on but it isn't heated. any ideas? all fuses working normally

Trident ribs shower

the best how to iv'e come across thank you.

This advice worked like a charm on our Aquas Aquamax shower. It is now getting to a nice warm temperature in the middle of winter. Thanks very much!

I don't have any connectors on the wire on mine, will I need to add these on if so do you have a link for the right ones. I have a triton alicante

So many views make me wonder if the issuenis not with triton pimps, the pressure is my house is rich but the shower is very poor and don't try to outnit in the second power because is just go hot and cold in loop...

Just fitted T80 Easi -fit plus but was unable to fit the bottom section due to not enough space because of pipe fittings but the main issue is I have power and light on the ON button but when pressed No water? Thanks for any advice

does the mails water need to be turned off when changing the Solenoid?

Just fitted same product, all work just fine, but I don't know if ok for the on off button to be light up all the time even if not in use.

If you don't push the plastic wall plugs behind the tiles, you're liable to crack the tiles as you tighten the screws.

There are some variations between Triton products that need to be mentioned. The manual for the T90 states "UNDER NO CIRCUMSTANCES MUST THE T90si BE CONNECTED DIRECTLY TO THE MAINS WATER SUPPLY". In fact, the minimum head required is only 8cm and the maximum head is 10m = 1 bar. I had to give this video a thumbs down for incomplete information.

In very cold weather, always check to see if the water supply pipe is not frozen before going after the solenoid valve. Have a look to see if the filter is blocked but you may need to bleed the air from pump before operating it again.

Just fitted one today...T90 sr .slightly different commissioning process... much easier ..I had a T90 si for about 18 years maybe longer ..Great shower good pressure & temp..a little disappointed with the temperature and pressure on new model...don't make them like they use too.

Not giving in off hot water any reason?

Informative!

My Triton won't turn off at the shower head only with the pull cord, could it need a new solenoid coil?